The Effect of Heat Treatment on Springing of AISI301
الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیک
Majid Karimian
1
(Islamic Azad University, Khomeinishahr Branch)
Ehsan Nourouzi Esfahani
2
(Young Researchers and elite club, Islamic Azad University, Khomeinishahr Branch)
Mohammad Bagherboom
3
(MSc., Department of Metallurgy Engineering, Isfahan University of Technology)
الکلمات المفتاحية: Thin spring steel plate, Martensite ά, Crystal Grain Size,
ملخص المقالة :
AISI 301 stainless steel is a frequently used metal, especially in high temperature demands and or in part with high corrosion risk. Thin spring steel plates can be used as expansions of heat furnaces insulation and variety of all other springs. The present study has assessed the effects of temperature and thermal treatment time span on the microstructure of stainless steel 301 to achieve elasticity and found out that microstructure gets smaller. As well as the Martensitic ά phase in the sample distributes uniformly after thermal treatment at 450 ºC for 20 minutes then water quenched in 10 ºC. By using X-ray diffraction, it can be found that the reduction in crystalline size of the Martensite ά and increasing in Martensite volume fraction is the cause of the elasticity of the samples. All obtained results confirmed by Ferittscope test.
[1] S.K Paul, N. Stanford, and T. Hilditch, "Austenite plasticity mechanisms and their behavior during cyclic loading," International Journal of Fatique., vol. 106, pp. 185-195, Jan 2018.
[2] W. Zeng, and H. Yuan, "Mechanical behavior and fatigue performance of austenitic stainless steel under consideration of martensitic phase transformation," Materials Science and Engineering., vol. 679, pp. 249-257, Jan 2017.
[3] S. Pirestany, A. Karmanpur, and A. Najafizadeh, "Effect of Operating Conditions on the Formation of Martensite Induced by Rolling Deformation and Resulted Morphology in 201 Austenitic Stainless Steel" Conference, Steel Symposium 93, Yazd, Ardakan Mineral and Industrial Company, Iran, vol. 1, Feb 2015.[in persian]
[4] P.M. Ahmedabadi, V. Kain, and A. Agrawal, "Modelling kinetics of strain-induced martensite transformation during plastic deformation of austenitic stainless steel," Materials & Design., vol. 109, pp. 466-475, Nov 2016.
[5] K.H. Lo, C.H. Shek, and J.K.L. Lai, "Recent developments in stainless steels," Materials Science and Engineering: R: Reports., vol. 65, pp. 39-104, May 2009.
[6] S. Pirestany, "Investigating the effect of strain-induced martensite morphology on formation of nano/ultra fine grained structure in 201 austenitic stainless steel through martensite themomechanical process," Isfahan University of Technology., Msc degree thesis, 2014.[in persian]
[7] W.S. Lee, and C.F. Lin, "The morphologies and characteristics of impact-induced martensite in 304L stainless steel," Scripta materialia., vol. 43, pp. 777-782, Sep 2000.
[8] M. Ahmadi, B.M. Sadeghi, and H. Arabi, "Experimental and numerical investigation of V-bent anisotropic 304L SS sheet with spring-forward considering deformation-induced martensitic transformation," Materials & Design., vol. 123, pp. 211-222, June 2017.
[9] S. Pirestany, A. Karmanpur, and A. Najafizadeh, "Effect of Martensite Induced by Strain Morphology on Microstructure Changes During Back Annealing after Thermo Mechanical Treatment of Martensite in 201 Austenitic stainless steel," Conference, Steel Symposium 94, Kish International Convention Center, Kish, Iran, vol. 1, Feb 2016.[in persian]
[10] F. Gauzzi, R. Montanari, G. Principi, and M.E. Tata, "AISI 304 steel: anomalous evolution of martensitic phase following heat treatments at 400 °C" Materials Science and Engineering: A., vol. 438-440, pp. 202-206, Nov 2006.
[11] P.L. Mangonon, and G. Thomas, "Structure and properties of thermal-mechanically treated 304 stainless steel," Metallurgical Transactions., vol. 1, pp. 1587-1594, June 1970.
[12] S. Bajda, W. Ratuszek, M. Krzyzanowski, and D. Retraint, "Inhomogeneity of plastic deformation in austenitic stainless steel after surface mechanical attrition treatment," Surface and Coatings Technology., vol. 329, pp. 202-211, Nov 2017.
[13] R. Naraghi," Martensitic Transformation in Austenitic Stainless Steels," Msc degree thesis, 2009.
[14] J. Singh, "Influence of deformation on the transformation of austenitic stainless steels," Journal of Materials Science., vol. 20, pp. 3157-3166, Sep 1985.
