Stress analysis of non-linearly variable thickness rotating disk in gas turbine engine using hyper-geometric method
الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیکBehrooz Shahriari 1 , Nedasadat Seddighi 2
1 - Faculty of Mechanics, Malek Ashtar University of Technology, Isfahan, Iran
2 - Mechatronic Sanaat sepahan Co. , Isfahan, Iran
الکلمات المفتاحية: Stress Analysis, Rotating disk, Gas turbine engine, Non-linearly variable thickness and density, Hyper-geometric method,
ملخص المقالة :
In this paper, the numerical and exact analytical calculation of elastic strains and stresses in gas turbine engine rotating disk with variable thickness, subjected to temperature gradient are presented. Galerkin method is applied to solve any kind of profiles with arbitrary thickness, temperature and density functions while the other numerical and analytical methods used in previous works, are applied to profiles with certain thickness functions. Therefore, a comprehensive approach that takes all the circumstances into account was used in an attempt to fill this gap. To verify the numerical method, a few examples of rotating disks with non-linear variable thicknesses were solved using the analytical method as a reference method and their results were compared with numerical solution. A good agreement between numerical and analytical solutions was observed. In the analytical part, a new method to convert equilibrium equation of rotating disks to hyper-geometric differential equation was provided and then it was solved. Using hyper-geometric method is the main novelty of this research. The distributions of radial displacement and stresses were obtained and an appropriate comparisons and discussions were made at the same environmental conditions.
[1] Timoshenko, S. (1956). Strength of Materials: Part 2, Advanced Theory and Problems. van Nostrand.
[2] Grammel, R. (1936). Neue Lösungen des Problems der rotierenden Scheibe. Ingenieur-Archiv, 7(3), 137-139.
[3] Thompson, A. S. (1946). Stresses in rotating disks at high temperatures.
[4] Pirmoradian, M. (2015). Dynamic stability analysis of a beam excited by a sequence of moving mass particles. Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, 8(1), 41-49.
[5] Torkan, E., Pirmoradian, M., & Hashemian, M. (2017). Occurrence of parametric resonance in vibrations of rectangular plates resting on elastic foundation under passage of continuous series of moving masses. Modares Mechanical Engineering, 17(9), 225-236.
[6] Sterner, S. C., Saigal, S., Kistler, W., & Dietrich, D. E. (1994). A unified numerical approach for the analysis of rotating disks including turbine rotors. International journal of solids and structures, 31(2), 269-277.
[7] You, L., Tang, Y., Zhang, J., & Zheng, C. (2000). Numerical analysis of elastic–plastic rotating disks with arbitrary variable thickness and density, International Journal of Solids and Structures, 37(52), 7809-7820.
[8] Torkan, E., & Pirmoradian, M. (2019). Efficient higher-order shear deformation theories for instability analysis of plates carrying a mass moving on an elliptical path. Journal of Solid Mechanics, 11(4), 790-808.
[9] Biezeno, C. B., & Grammel, R. (2013). Technische dynamic. Springer-Verlag.
[10] Dubbel, H. (2013). DUBBEL: Taschenbuch für den Maschinenbau. Springer-Verlag.
[11] Stodola, A. (1924). Mit einem Anhang über die Aussichten der Wärmekraftmaschinen. Springer Berlin.
[12] Honegger, V. E. (1927). Festigkeitsberechnung von rotierenden konischen Scheiben. ZAMM‐Journal of Applied Mathematics and Mechanics/Zeitschrift für Angewandte Mathematik und Mechanik, 7(2), 120-128.
[13] Giovannozzi, R. (1956). Calculation, tabulation and uses of some functions occurring in the theory of the conical disc subjected to centrifugal and thermic stress. Proceedings of II Congresso Aeronautico Europeo (pp. 30.31-30.12), Scheveningen.
[14] Güven, U. (1995). Tresca's yield condition and the linear hardening rotating solid disk of variable thickness. ZAMM‐Journal of Applied Mathematics and Mechanics/Zeitschrift für Angewandte Mathematik und Mechanik, 75(10), 805-807.
[15] Orcan, Y., & Eraslan, A. N. (2002). Elastic–plastic stresses in linearly hardening rotating solid disks of variable thickness. Mechanics Research Communications, 29(4), 269-281.
[16] Eraslan, A. N., & Argeso, H. (2002). Limit angular velocities of variable thickness rotating disks. International Journal of Solids and Structures, 39(12), 3109-3130.
[17] Eraslan, A.N. (2005). A class of nonisothermal variable thickness rotating disk problems solved by hypergeometric functions. Turkish Journal of Engineering and Environmental Sciences, 29(4), 241-269.
[18] Vivio, F., & Vullo, V. (2007). Elastic stress analysis of rotating converging conical disks subjected to thermal load and having variable density along the radius. International Journal of Solids and Structures, 44(24), 7767-7784.
[19] Hojjati, M., & Jafari, S. (2008). Semi-exact solution of elastic non-uniform thickness and density rotating disks by homotopy perturbation and Adomian's decomposition methods. Part I: Elastic solution. International Journal of Pressure Vessels and Piping, 85(12), 871-878.
[20] Zenkour, A. M., & Mashat, D. S. (2010). Analytical and numerical solutions for a rotating annular disk of variable thickness. Applied Mathematics, 1(5), 431.
[21] Zenkour, A. M., & Mashat, D. S. (2011). Stress function of a rotating variable-thickness annular disk using exact and numerical methods. Engineering, 3(4), 422.
[22] Nejad, M. Z., Jabbari, M., & Ghannad, M. (2014). A semi-analytical solution for elastic analysis of rotating thick cylindrical shells with variable thickness using disk form multilayers. The Scientiic World Journal, Vol. 2014, ID 932743, 10 pages.
[23] Zamani Nejad, M., Jabbari, M., & Ghannad, M. (2014). Elastic Analysis of Rotating Thick Truncated Conical Shells Subjected to Uniform Pressure Using Disk Form Multilayers. ISRN Mechanical Engineering, Vol. 2014, http://dx.doi.org/10.1155/2014/764837
[24] Bagheri, E., Asghari, M., & Danesh, V. (2019). Analytical study of micro-rotating disks with angular acceleration on the basis of the strain gradient elasticity. Acta Mechanica, 230(9), 3259-78.
[25] Abdalla, H.M., Casagrande, D., & Moro, L. (2020). Thermo-mechanical analysis and optimization of functionally graded rotating disks. The Journal of Strain Analysis for Engineering Design, 55(5-6), 159-71.
[26] Sharma, D., Kaur, R., & Sharma, H. (2021). Investigation of thermo-elastic characteristics in functionally graded rotating disk using finite element method. Nonlinear Engineering, 10(1), 312-22.
[27] Vullo, V., & Vivio, F. (2013). Rotors: Stress analysis and design, Springer Science & Business Media.
[28] Zienkiewicz, O. C., Taylor, R. L., & Zhu, J. Z. (2005). The finite element method: its basis and fundamentals. Elsevier.
[29] Gasper, G., Rahman, M., & George, G. (2004). Basic hypergeometric series. Cambridge university press.
[30] Aomoto, K., Kita, M., Kohno, T., & Iohara, K. (2011). Theory of hypergeometric functions. Springer.
