Investigation of Axial to Lateral Load ratio on the Buckling of Thin Orthotropic Cylindrical Shells

الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیک

مسیب اسماعیل دخت ¹ (دانشجوی کارشناسی ارشد، دانشکده مهندسی مکانیک، دانشگاه صنعتی نوشیروانی بابل)
رضا اکبری آلاشتی ² (دانشیار، دانشکده مهندسی مکانیک، دانشگاه صنعتی نوشیروانی بابل)
محمدحسن قاسمی ³ (استادیار، دانشکده مهندسی مکانیک، دانشگاه صنعتی نوشیروانی بابل)
مرتضی دردل ⁴ (استادیار، دانشکده مهندسیمکانیک، دانشگاه صنعتی نوشیروانی بابل)

تاريخ الإرسال : 25 السبت , محرم, 1437 تاريخ التأكيد : 25 السبت , محرم, 1437 تاريخ الإصدار : 30 الإثنين , صفر, 1436

الکلمات المفتاحية: FEM, Buckling, Orthotropic, Cylindrical shells, axial load to lateral pressure ratio,

ملخص المقالة :

Buckling analysis of thin cylindrical shells is very important due to their production process. Usually longitudinal and transversal stiffeners are used to increase the buckling stiffness. In this paper, considering a thin cylindrical shell with longitudinal and transversal ribs subjected to axial force and lateral pressure, the influence of different aspect of axial force to lateral pressure on buckling load is investigated for different ratios such as thickness to radius and length to radius. The analytical results based on Donnell’s classical linear stability equations for anisotropic cylindrical shells are compared with FEM results of ANSYS software. The results show that the analytical method of Donnell can be used for special aspect ratios. Furthermore, by increasing the axial to lateral load ratio, the axial buckling load is increased for most of the aspect ratios, while the lateral buckling load decreases.

المصادر:

[1] Kenny partners J.P., Buckling of Offshore Structural Components, Report of the UK Cohesive Buckling Research Programme, 1983-1985, London, 1992, p.259. [2]آلمورث ب.، براشد.، کمانش میله­ها، ورق­ها و پوسته­ها، ترجمه مجتبی قمری زاده و غلامحسین رحیمی، تهران: انتشارات دانشگاه امام حسین (ع)،  1383. [3] Bai y., Marine structural design, Elsevier, 2003, Houston, America. [4] SlizR., Chang M.Y., Reliable and accurate prediction of the experimental buckling of thin-walled cylindrical shell under an axial load, Thin-Walled Structures, Vol. 49, 2010,pp. 409-421. [5] Iwicki P., Tejchman J., Chróścielewski J., Dynamic FE simulations of buckling process in thin-walled cylindrical metal silos, Thin-Walled Structures, Vol. 84, 2014, pp. 344-359. [6] Rathinam N., Prabu B., Numerical study on influence of dent parameters on critical buckling pressure of thin cylindrical shell subjected to uniform lateral pressure, Thin-Walled Structures, Vol. 88, 2015, pp. 1-15. [7] Sofiyev A., Kuruoglu N., Buckling analysis of nonhomogeneous orthotropic thin-walled truncated conical shells in large deformation, Thin-Walled Structures, Vol. 62, 2013, pp. 131-141, [8] Yang L., Luo Y., Qiu T., Yang M., Zhou G., Xie G., An analytical method for the buckling analysis of cylindrical shells with non-axisymmetric thickness variations under external pressure, Thin-Walled Structures, Vol. 82, 2014, pp. 431-440. [9] Pinna R., Buckling and collapse of cylinders with one end open and one end simply supported with varying axial restraint, International Journal of mechanical sciences, Vol. 46, 2004,  pp. 541-559. [10] Kim S.E., Buckling strength of the cylindrical shell and tank subjected to axially compressive loads, Thin-walled structures, Vol. 40, 2002, pp. 329-353. [11] Baruch M., Singer J., Effect of Eccentricity of Stiffeners on the General Instability of Stiffened Cylindrical Shells under Hydrostatic pressure, Archive Journal of Mechanical Engineering Science, Vol. 5, No. 1, 1963, pp. 23-27. [12] Singer J., Baruch M., Harari O., On the Stability of Eccentrically Stiffened Cylindrical Shells under Axial Compression,On the Stability of Eccentrically Stiffened Cylindrical Shells under Axial Compression, International Journal of Solids and Structures,Vol. 3, No. 1, 1967, pp. 445-470. [13] FluggeW., Stresses in Shells,Second Edition, Springer, 1973, Verlag Berlin.