Investigating and evaluating the behavior of the proposed connection in the steel bending frame
الموضوعات :
مهری عسگری
1
,
محمد رضا ادیب رمضانی
2
1 -
2 - گروه مهندسی عمران ، واحد تهران جنوب ،دانشگاه آزاد اسلامی، تهران، ایران
الکلمات المفتاحية: steel connection, Abaqus finite element software, 2800 standard, nonlinear static analysis of time history.,
ملخص المقالة :
In this study, the pre-approved connection and the proposed connection have been investigated and analyzed using Abaqus finite element software. Non-linear static analysis was performed with reciprocating loading. In this study, in order to compare the proposed connection and the direct connection, two one-story and six-story frames has been modeled and the behavior of the two connections in these frames has been investigated. According to the software models, it can be seen that in all the models, the bending moment capacity of the connection is more than 40% of the calculated plastic moment in the connection. In connection with the reduced cross-section, this percentage has reached nearly 20%. The results of the proposed connection behavior show that it performs nearly 25-34% better than the pre-validated connection of the 10th topic of Iran regulation of structures. The structure with the proposed connection has a higher coefficient of behavior than direct connection. With the increase in the height of the structure, the coefficient of behavior of the structure has also decreased.
1. Hanson, N.W., Conner, H.W., “Seismic Resistance of Reinforced Concrete BeamColumn Joints”, Journal of Structural Division, ASCE, V. 93, ST. 5, Oct 1967.
2. Ehsani, M. R. and Wight, J. K., “Exterior Reinforced Concrete Beam to Column Connection Subjected to Earthquake-Type Loading”, ACI journal, pp. 402- 499, 1985.
3. Durrani, A. J., and Wight, J. K., “Experimental and Analytical Study of Internal Beam to Column Connections Subjected to Reversed Cyclic Loadings”, Report No. UMEE 82R3, Department of Civil Engineering, University of Michigan, Ann Arbor, Mich., 275, 1982.
4. ACI-ASCE Committee 352, “Recommendations ]9[ for Design of Beam Column Joints in Monolithic Reinforced Concrete Structures”, ACI Journal, Vol. 82, No. 3, pp. 266- 283, May- June 1985. ACI-ASCE Committee 352, Recommendations ]10[ for design of Beam-Column Joints in Monolithic Reinforced Concrete Structures, ACI 352R- 91, Re-approved, 1997.
5. Li, L., Wang, W., Chatzi, E., & Ghafoori, E. (2023). Experimental investigation on debonding behavior of Fe-SMA-to-steel joints. Construction and Building Materials, 364, 129857.
6. Mohabeddine, A., Malik, G., Correia, J., Silva, F., De Jesus, A., Fantuzzi, N., & Castro, J. M. (2023). Experimental parametric investigation on the behavior of adhesively bonded CFRP/steel joints. Composite Structures, 307, 116598.
7. Ha, G. J., Kim, J. K. and Chung L.,“Response of Reinforced High- Strength Concrete BeamColumn Joints Under Load Reversals”, Magazine of Concrete Research, Vol. 44, No. 160, pp. 175- 184, 1992.
8. Houshmand-Sarvestani, A., Totonchi, A., Shahmohammadi, M. A., & Salehipour, H. (2023). Numerical assessment of the effects of ADAS yielding metallic dampers on the structural behavior of steel shear walls (SSWs). Mechanics Based Design of Structures and Machines, 51(3), 1626-1644.
9. Li, J., Wang, Y., Zhang, Z., & Mou, B. (2023). Seismic behavior of steel frames with different joints: Shaking table test and finite element analysis. Journal of Building Engineering, 70, 106377.
10. Ganesan, N., Indira P.V. and Abraham, R., “Steel Fiber Reinforced High Performance Concrete Beam-Column Joints Subjected to Cyclic Loading”, ISET Journal of Earthquake Technology, Vol. 44, No. 3- 4, , pp. 445– 456, Sept. Dec, 2007
11. Shannag, M.J., Abu-Dyya, N. and Abu-Farsakh, G., “Lateral Load Response of HighPerformance Fiber Reinforced Concrete Beam-Column Joints”, Construction and Building Materials,Vol. 19, No. 7, pp. 500– 508, 2005.
12. Roudsari M Tahamouli, Jamshidi H, Moradi SH. Experimental and numerical assessment of reduced IPE beam sections connections with box-stiffener. Int J Steel Struct 2018;18(1):255–63.
13. Sang .JuL.EE , Sang. E. H. , Sam Y. N. , Sung .W. S.," Deformation Capacity of Reduced Beam Section Moment Connection by Staggered Holes" , Proceedings of the International Conference on Sustainable Building Asia, Seoul, Korea, 27 29 June 2007.
14. Farrokhi. H., Danesh. F., Eshghi. S., "A modified moment resisting connection for ductile steel frames (Numerical and experimental investigation)"Journal of Constructional Steel Research 65 (2009) 2040–2049.
15. Shahu, A., Hiwase, P. D., Choudhari, A. S., & Shangondawar, M. (2020). Comparison on Sustainability of Moment Resistance Connection Methods in Steel Design. Helix, 10(01), 200-203..
16. American Institute of Steel Construction (AISC). " Seismic Specifieation for Structural Steel Buildings" Chicago . IL. (2005).
17. FEMA -355 D. ," State of Art Report on Connection Performance " , Prepared by the SAC Joint Venture for the Federal Emergency Management Agency , Washington ,September , 2000.
18. El-Tawil ,S., Mikesell . T.,Vidarsson. E., and Kunnath. SK .," Strength and ductility of FR Welded-bolted Connection" ,SAC Report 98-1 .sacramento ,calif ., SAC Joint Venture 1998.
19. Shin, Kyung-Jae, Young-Ju Kim, and Young-Suk Oh. "Seismic behaviour of composite concrete-filled tube column-to-beam moment connections." Journal of Constructional Steel Research 64, no. 1 (2008): 118-127.
20. Wang, P., Wang, Z., Pan, J., Zheng, Y., & Liu, D. (2019). Cyclic Behavior of Steel Beam to CFT Column Connections with Gusset Plates. Advances in Civil Engineering, 2019.
21. Krawinkler, H., Bertero, V., Popov, E.P,. Inelastic behavior of steel beam-to-column subassemblages. Earthquake Ebgineering Research Center. 1971.
