Fabrication, Testing and Analysis of Composite Lattice Panels Under Three-Point Bending Load

الموضوعات :

Mahdi Farhadi ¹ (University Complex of Materials and Manufacturing Technology, Malek Ashtar University of Technology, Lavizan, Tehran, Iran.)
Ali Davar ² (Faculty of Materials and Manufacturing Processes, Malek Ashtar University of Technology, Iran)
Mohsen Heydari Beni ³ (University Complex of Materials and Manufacturing Technology, Malek Ashtar University of Technology, Lavizan, Tehran, Iran.)
Jafar Eskandari Jam ⁴ (Professor, Department of Mechanical Engineering, Composite Engineering Research Institute, Malek Ashtar University of Technology, Tehran, Iran.)

تاريخ الإرسال : 19 الإثنين , محرم, 1442 تاريخ التأكيد : 18 الأربعاء , جمادى الأولى, 1443 تاريخ الإصدار : 17 الأحد , ذو الحجة, 1445

الکلمات المفتاحية: numerical analysis, Three-point bending test, Glass/Epoxy, Composite lattice panel,

ملخص المقالة :

Thanks to their high strength-to-weight ratio, lightweightness, and excellent energy absorption, composite lattice panels can be used in the aerospace, marine, automotive, and other industries. These structures can be used as an alternative to string-reinforced structures, honeycomb (core) sandwich panels, and aluminum grid structures. In this paper, a composite lattice panel is first fabricated from glass/epoxy by hand lay-up method using a silicon rubber mold. In this method, a Kagome composite lattice panel with twelve layers of resin-impregnated fibers was fabricated during a continuous process. After fabrication, the test panel was shown under three-point bending and failure modes. Also, a numerical simulation of three-point bending was performed in ABAQUS software. Then, the simulation results were compared with those of the experimental test, indicating a good convergence between the experimental test results and the finite element ones up to the point of failure. Due to changes in directions of force, these structures have a high ability to withstand damage, and therefore, continue to withstand the load after the failure of one or more ribs. Also, there is no sudden and sharp drop in the load-bearing capacity of the structure despite the force being maximized, which can be attributed to the high energy absorption of such structures. Instead, the force decreases slowly with fluctuations, and the structure continues to absorb energy until final failure. Therefore, such lightweight structures can be used in applications where energy absorption is of great importance.

المصادر:

[1] Jadhav, P., Mantena, P. R., Parametric Optimization of Grid-Stiffened Composite Panels for Maximizing Their Performance Under Transverse Loading, Composite Structures, Vol. 77, 2007, pp. 353-363.
[2] Kim, T. D., Fabrication and Testing of Thin Composite Isogrid Stiffened Panel, Composite Structures, Vol. 49, 2000, pp. 21-25.
[3] S. S. Shenoy, S. S., Energy Absorption of a Car Roof Reinforced with A Grid Stiffened Composite Panel in The Event of a Rollover, Wichita State University, 2006.
[4] Kim, T. D., Fabrication and Testing of Composite Isogrid Stiffened Cylinder, Composite Structures, Vol. 45, 1999, pp. 1-6.
[5] Huybrechts, S. M., Meink, T. E., Wegner, P. M., and Ganley, J. M., Manufacturing Theory for Advanced Grid Stiffened Structures, Composites Part A: Applied Science and Manufacturing, Vol. 33, 2002, pp. 155-161.
[6] Gan, C. Gibson, R. F., and Newaz, G. M., Analytical/Experimental Investigation of Energy Absorption in Grid-Stiffened Composite Structures Under Transverse Loading, Experimental Mechanics, Vol. 44, 2004, pp. 185-194.
[7] Fan, H., Meng, F., and Yang, W., Sandwich Panels with Kagome Lattice Cores Reinforced by Carbon Fibers, Composite Structures, Vol. 81, 2007, pp. 533-539.
[8] Muthyala, V. D., Composite Sandwich Structure with Grid Stiffened Core, M.Sc. Thesis, Louisiana State University, 2007.
[9] Fan, H., Yang, L., Sun, F., and Fang, D., Compression and Bending Performances of Carbon Fiber Reinforced Lattice-Core Sandwich Composites, Composites Part A: Applied Science and Manufacturing, Vol. 52, 2013, pp. 118-125.
[10] Ahmadi, T., Khalili, M., Analysis of Composite Sandwich Panels with Grid Stiffened Core Under Tensile Load, MSc Thesis, Department of Mechanical Engineering, Khajeh Nasir University of Technology (In Persian).
[11] Mahmoudi, Azarafza, R., and Davar, A., Design Manufacturing and Bending Testing of Composite Sandwich Panels Reinforced with Grid Core, In the 20th International Conference of Mechanical Engineering, 1393 (In Persian).
[12] Vasiliev, V., Barynin, V., and Rasin, A., Anisogrid Lattice Structures–A Survey of Development and Application, Composite structures, Vol. 54, 2001, pp. 361-370.
[13] Jadhav, P., Mantena, P. R., and Gibson, R. F., Energy Absorption and Damage Evaluation of Grid Stiffened Composite Panels Under Transverse Loading, Composites Part B: Engineering, Vol. 37, 2006, pp. 191-199.
[14] Dow, N. F., Rosen, B. W., Evaluations of Filament-Reinforced Composites for Aerospace Structural Applications, DTIC Document, 1965.