Subject Areas : journal of New Materials

مجید پورانوری ¹ (مربی، دانشگاه آزاد اسلامی، واحد دزفول، دزفول، ایران)
پیروز مرعشی ² (استادیار، دانشگاه صنعتی امیرکبیر، تهران، ایران)

Received: 2015-12-29 Accepted : 2015-12-29 Published : 2012-06-21

Keywords:

References:

1- A. Bag, K. Ray K, Dwarakadasa E.S.,"Influence of martensite content and

morphology on the toughness and fatiguebehavior of high-martensite dual-phase steels",

Metallurgical and Materials Transactions A,Vol.32, pp. 2207-2217, 2001.

2- M. D.Tumuluru, "Resistance spot weldingof coated high-strength dual phase steels",

Weld J. ,Vol. 87,pp.31-37,2007

3- H. Zhang, J. Senkara, Resistance welding:fundamentals and applications, Taylor &

Francis CRC press, 2005.

4- M. Pouranvari, A. Abedi, P. Marashi, M.Goodarzi, "Effect of expulsion on peak load

and energy absorption of low carbonresistance spot welds", Sci. Technol. Weld.

Joining, Vol. 13, pp.39-43, 2008.

5- Y. J. Chao, "Failure Mode of ResistanceSpot Welds: Interfacial Versus Pullout", Sci.

Technol. Weld. Joining, Vol. 8, pp. 133-137,2003.

6- M. Pouranvari, H. R. Asgari, S. M.Mosavizadeh, P. H. Marashi and M. Goodarzi,

"Effect of Weld Nugget Size on OverloadFailure Mode of Resistance Spot Welds", Sci.

Technol. Weld. Joining, Vol. 12, pp. 217-225,2007.

7- M. Pouranvari, S.P.H. Marashi, Key factorsinfluencing mechanical performance of dual

phase steel resistance spot welds, Sci TechnolWeld Join, Vol15,pp.149-155, 2010.

8- X. Sun, E.V. Stephens, M.A. Khaleel,Effects of fusion zone size and failure mode

on peak load and energy absorption ofadvanced high strength steel spot welds under

lap shear loading conditions, Eng. Fail. Anal.,Vol.15,pp.356-367,2008.

9- M. Marya, K. Wang, L. G. Hector, X.Gayden, Tensile-Shear Forces and Fracture

Modes in Single and Multiple WeldSpecimens in Dual-Phase Steels, J. Manufact.

Sci. Eng., Vol.128, pp. 287-298, 2006.

10- M. Alenius, P. Pohjanne, Somervuori M.,Hanninen H., " Exploring the Mechanical

Properties of Spot Welded Dissimilar Joints for Stainless and Galvanized Steels", Weld.

J., Vol.85,pp.305s–313s, 2006.

11- P. Marashi, M. Pouranvari, S.Amirabdollahian, A. Abedi, M. Goodarzi,

"Microstructure and Failure Behavior oDissimilar Resistance Spot Welds between

Low Carbon Galvanized & AusteniticStainless Steels", Mater. Sci Eng. A,

Vol.480,pp.175-180,2008.

12- S. Poggio, M. Ponte, C. Gambaro, J.Adamowski, Resistance spot welding of

advanced high strength steel DP600, SuperHigh Strength Steels. Proc. 1st International

Conference, Rome, pp.1-13, 2005.

13- S. Daneshpour, S. Riekehr, M. Kocak andC. H. J. Gerritsen, Mechanical and fatigue

behaviour of laser and resistance spot weldsin advanced high strength steels وSci.

Technol. Weld. Joining, 14, 20-25, 2009.

14- M.S. Khan, S.D. Bhole, D.L. Chen, E.Biro, G. Boudreau, J. van Deventer, " Welding

behaviour, microstructure and mechanicalproperties of dissimilar resistance spot welds

between galvannealed HSLA350 and DP600steels", Sci. Technol. Weld. Joining, Vol.14,

pp.616-625, 2009.

15- V. H. B. Hernandez, M. L. Kuntz, M. I.Khan, Y. Zhou, "Influence of weld size and

microstruture of dissimilar AHSS resistancespot welds ", Sci. Technol. Weld.

Joining,Vol.13, pp.769-776, 2008.

16- M. Marya, X.Q. Gayden, "Development ofRequirements for resistance Spot Welding

Dual-Phase (DP600) Steels Part 2: StatisticalAnalyses and Process Maps", Weld J., Vol.

84, pp.197s–204s, 2005.

17- ‘Recommended practices for test methodsand evaluation the resistance spot welding

behavior of automotive sheet steels’,ANSI/AWS/SAE D8?9-97, 1997.

18- J. E. Gould, S. P. Khurana, T. Li,"Predictions of microstructures when welding

automotive advanced high-strength steels",Weld J., Vol. 86, pp.111s-116s, 2006.

19- M. Milititsky, E. Pakalnins, C. H. Jiang A.Thompson, "On characteristics of DP600

resistance spot welds", SAE Report 2003-01-0520, Warrendale, PA, USA, 2003.

20-http://homepage3.nifty.com/yurioka/ exp.Html