Advanced Manufacturing Technology by Under Water Friction Stir Welding Technique

Subject Areas : Journal of Environmental Friendly Materials

M Sadeghi ¹ , M Farahani ² , H Sabet ³

1 - Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran
2 - Department of Materials Engineering, Baker Hughes a GE Company, Australia
3 - Department of Materials Engineering, Karaj Branch, Islamic Azad University, Karaj, Iran

Received: 2022-11-10 Accepted : 2023-03-11 Published : 2023-06-01

Keywords: Friction Stir Welding, Under Water, Advanced Manufacturing,

References:

[1] D. Kumar Rajak, D. D. Pagar, P. L. Menezes, and A. Eyvazian, J. Adhesion Sci. Tech., vol. 34, no. 24, 2020, pp. 2613.

[2] Shahabuddin, V. K. Dwivedi, A. Sharma, Int. J. Eng. Adv. Tech. (IJEAT), Vol.8, No.4, 2019.

[3] I. Sabry and A. M.El-Kassas, Int. J. Eng. Tech., 2019, 11, 78.

[4] Mohd. Atif Wahid, Rev. Trans. Nonferr. Meta. Soc. China, 2018, 28, 193.

[5] A. M. El-Kassas, J. Adv. Eng. Tech. 4, 2017, 158.

[6] I. Sabry, I. Mourad and D. T. Thekkuden, Inter. Rev. of Aerosp. Eng. 14, 2020, 64.

[7] H. Papahn, Int. J. of Adv. Manuf. Tech., 78, 2015, 1101.

[8] H. J. Liu, H. J. Zhang and L. Yu , Mat. Des. 32, 2011, 1548.

[9] S. K Maiti, S. Namdeo and I. Mourad, Nucl. Eng. Des. 238, 2008, 787.

[10] L. Aaron, Stahl, Experimental measurements of longitudinal load distributions on friction stir weld pin tool, Depart. Mech. Eng. Brigham Young University, 2005.

[11] R. S. Mishra and Z. Y. Ma, Inst. Metal Res., A Rev. J. Chinese Academy Sci., Shenyang 110016, China, 2005.

[12] T. S. Srivatsan and S. Vasudevan, Depart. Mech. Eng., Cincinnati, Ohio, USA, 2006,15.

[13] Ku¨ c¸u¨ k€omero_glu T, Aktarer SM, _Ipeko_glu G, C¸ G. Am, Int. J. Min. Met. Mater. 2018; 25:1457-64.

[14] M. Imam, V. Racherla, K. Biswas, H. Fujii, V. Chintapenta, Y. Sun, et al., Int. J. Adv. Manuf. Technol., 2017; 91:1753-69.

[15] V. M. Magalh~aes, C. Leit~ao and DM.. Rodrigues, Res. Status. Sci. Technol. Weld Join 2018; 23:400-9.

[16] X. Meng, Y. Huang, J. Cao, J. Shen and JF. dos Santos, Prog. Mater. Sci., 2021; 115:100706.

[17] P. L. Threadgill, 'Friction stir welds in aluminium alloys: Preliminary microstructural assessment', TWI Bulletin, March/April 1997.