The Effect of the Mg Content on Mechanosynthesis of ZrB2–SiC–ZrC Composite in the Mg/ZrSiO4/B2O3/C System

Subject Areas : Materials synthesis and charachterization

Omid Torabi ¹ , Sanaz Naghibi ² , Mohammad Hossein Golabgir ³ , Hamid Tajizadegan ⁴ , Amin Jamshidi ⁵

1 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Isfahan, Iran
2 - Department of Ceramic Engineering, Shahreza Branch, Islamic Azad University, Isfahan, Iran.
3 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Isfahan, Iran
4 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Isfahan, Iran
5 - Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Isfahan, Iran

Received: 2014-11-28 Accepted : 2015-01-05 Published : 2015-04-01

Keywords:

References:

1. X. Zhang, Q. Qu, J. Han, W. Han, C. Hong, “Microstructural features and mechanical properties of ZrB2–SiC–ZrC composites fabricated by hot pressing and reactive hot pressing”, Scripta Mater., Vol. 59, 2009,
   pp. 753–756.


2.  H. Y. Ryu, H. H. Nersisyan, J. H. Lee, “Preparation of zirconium-based ceramic and composite fine-grained powders”, Int. J. Refract. Met. Hard Mater., Vol. 30, 2012, pp. 133–138.


3. Q. Qiang, Z. Xinghong, M. Songhe, H. Wenbo, H. Changqing, H. Jiecai, “Reactive hot pressing and sintering characterization of ZrB2–SiC–ZrC composites”, Mater. Sci. Eng. A., Vol. 491, 2008, pp. 117–123.


4. T. Tsuchida, S. Yamamoto, “Mechanical activation assisted self-propagating high-temperature synthesis of ZrC and ZrB2 in air from Zr/B/C powder mixtures”, J. Eur. Ceram. Soc. Vol. 24, 2004, pp. 45–51. 


5. W. W. Wu, G. J. Zhang, Y. M. Kan, P. L. Wang, “Combustion synthesis of ZrB2–SiC composite powders ignited in air”, Mater Lett., Vol. 63, 2009, pp. 1422–1424.


6. R. Licheri, R. Orrù, C. Musa, G. Cao, “Combination of SHS and SPS Techniques for fabrication of fully dense ZrB2-ZrC-SiC composites”, Mater Lett. Vol. 6, 2008,
   pp. 432–435.


7. Y. Li, W. Han, H. Li, J. Zhao, T. Zhao, “Synthesis of nano-crystalline ZrB2/ZrC/SiC ceramics by liquid precursors”, Mater Lett., Vol. 68, 2012, pp.101–103.


8. M. Jalaly, M. Tamizifar, M. Sh. Bafghi, F. J. Gotor, “Mechanochemical synthesis of ZrB2–SiC–ZrC nanocomposite powder by metallothermic reduction of zircon”, J. Alloy. Compd., Vol. 581, 2013, pp. 782–787.


9. O. Torabi, R. Ebrahimi-Kahrizsangi, “Effect of the aluminum content on the mechanochemical behavior in ternary system Al–B2O3–C”, Int. J. Refract. Met. Hard Mater., Vol. 36, 2013,
   pp. 90–96.


10. 10. M. Yaghoubi, O. Torabi, “Effect of the magnesium content on the mechanochemical behavior in ternary system Mg–B2O3–C”, Int. J. Refract. Met. Hard Mater., Vol. 43, 2014, pp. 132–140.


11. 11. A. K. Khanra, “Reaction chemistry during self-propagating high-temperature synthesis (SHS) ofH3BO3–ZrO2–Mg system”, Mater. Res. Bull., Vol. 42, 2007, pp. 2224–2229.


12. 12. P. Balaz, Mechanochemistry in nanoscience and minerals engineering, 1st ed., Springer Berlin Heidelberg, Germany, 2008, p. 14.


13. 13. L. Takacs, “Self-Sustaining Reactions Induced by Ball Milling: An Overview”, Int. J. SHS., Vol. 18, 2009, pp. 276-282.


14. 14. C. Suryanarayana, “Mechanical alloying and milling”, prog. Mater. Sci., Vol. 46, 2001, pp. 1–184.


15. 15. O. Kubaschewski, C. B. Alcock, Metallurgical thermochemistry, 4th ed., Pergamon Press, UK, 1979, p. 360.


16. 16. A. J. Nikkhah, O. Torabi, R. Ebrahimi-Kahrizsangi, S. Naghibi, A. Jamshidi, InvestigationonmechanochemicalsynthesisofAl2O3/BN nanocomposite by aluminothermic reaction, Cer. Int., Vol. 40, 2014, pp. 5559–5566.


17. M. Sakaki, M. S. Bafghi, J. Vahdati Khaki, Q. Zhang, J. Kano, F. Saito, “Effect of the aluminum content on the behavior of mechanochemical reactions in the WO3–C–Al system”, J. Alloy. Compd., Vol. 480, 2009, pp. 824–829