Numerical investigation of strain distribution during cyclic expansion extrusion (CEE)

Subject Areas : Chemistry

Hamid Reza Torabi ¹ (Department of Mechanical Engineering, Faculty of Eng. , University of Tehran, Tehran, Iran)
M.M. Samandari ² (Department of Mechanical Engineering, Faculty of Eng. , University of Tehran, Tehran, Iran)
Ghader Faraji ³ (Department of Mechanical Engineering, Faculty of Eng. , University of Tehran, Tehran, Iran)
Abolfazl Masoumi ⁴ (Department of Mechanical Engineering, Faculty of Eng. , University of Tehran, Tehran, Iran)

Received: 2015-02-27 Accepted : 2015-07-02 Published : 2015-04-01

Keywords:

References:

1. Horita, Z., Nanomaterials by Severe Plastic Deformation. International Conference on Nanomaterials by Severe Plastic Deformation 2006: Materials Science Forum. 1050.


2. Rosochowski, A., Processing metals by severe plastic deformation. Solid State Phenomena, 101, 2004, pp. 13-22.


3. Rosochowski, A., L. Olejnik, and M. Richert, Metal forming technology for producing bulk nanostructured metals. Journal of Steel and Related Materials–Steel GRIPS, 2, 2004, pp. 35-44.


4. Valiev, R., et al., Producing bulk ultrafine-grained materials by severe plastic deformation.JOM, 58(4), 2006, pp. 33-39.


5. Azushima, A., et al., Severe plastic deformation (SPD) processes for metals.CIRP Annals - Manufacturing Technology, 57(2), 2008, pp. 716-735.


6. Babaei, A. and M. M. Mashhadi, Characterization of ultrafine-grained aluminum tubes processed by Tube Cyclic Extrusion–Compression (TCEC). Materials Characterization, 95(0), 2014, pp. 118-128.


7. Valiev, R. Z. and T. G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement. Progress in Materials Science, 51(7), 2006, pp. 881-981.


8. Huang, X., et al., Microstructural evolution during accumulative roll-bonding of commercial purity aluminum. Materials Science and Engineering: A, 340(1–2), 2003, pp. 265-271.


9. Saito, Y., et al., Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process. Scripta Materialia, 39(9), 1998, pp. 1221-1227.


10. 10. Zhilyaev, A. P., et al., Experimental parameters influencing grain refinement and microstructural evolution during high-pressure torsion. Acta Materialia, 51(3), 2003, pp. 753-765.


11. 11. Zhilyaev, A. P. and T. G. Langdon, Using high-pressure torsion for metal processing: Fundamentals and applications. Progress in Materials Science, 53(6), 2008, pp. 893-979.


12. 12. Richert, M., Q. Liu, and N. Hansen, Microstructural evolution over a large strain range in aluminium deformed by cyclic-extrusion–compression. Materials Science and Engineering: A, 260(1), 1999, pp. 275-283.


13. 13. Zhang, J. A new bulk deformation method–Cyclic extrusion. in Materials Science Forum. 2007. Trans Tech Publ.


14. 14. Faraji, G., et al., TEM analysis and determination of dislocation densities in nanostructured copper tube produced via parallel tubular channel angular pressing process. Materials Science and Engineering: A, 563(0), 2013, pp. 193-198.


15. 15. Faraji, G. and M. Mousavi Mashhadia, Plastic deformation analysis in parallel tubular channel angular pressing (PTCAP). Journal of Advanced Materials and Processing, 1(4), 2013, pp. 23-32.


16. 16. Pardis, N., et al., Cyclic expansion-extrusion (CEE): A modified counterpart of cyclic extrusion-compression (CEC). Materials Science and Engineering: A, 528(25–26), 2011, pp. 7537-7540.


17. 17. Babaei, A., M. M. Mashhadi, and H. Jafarzadeh, Tube cyclic expansion-extrusion (TCEE) as a novel severe plastic deformation method for cylindrical tubes. Journal of Materials Science, 49(8), 2014, pp. 3158-3165.


18. 18. Pardis, N., et al., Development of new routes of severe plastic deformation through cyclic expansion–extrusion process. Materials Science and Engineering: A, 613(0), 2014, pp. 357-364.


19. 19. Lin, J.-b., et al., Finite element analysis of strain distribution in ZK60 Mg alloy during cyclic extrusion and compression. Transactions of Nonferrous Metals Society of China, 22(8), 2012, pp. 1902-1906.


20. 20. Lin, J., et al., Study on deformation behavior and strain homogeneity during cyclic extrusion and compression. Journal of Materials Science, 43(21), 2008, pp. 6920-6924.


21. 21. Rosochowski, A., R. Rodiet, and P. Lipinski, Finite element simulation of cyclic extrusion-compression. Metal Forming, 2000, pp. 253-259.


22. 22. Azimi, A., et al., Mechanical properties and microstructural evolution during multi-pass ECAR of Al 1100–O alloy. Materials & Design, 42(0), 2012, pp. 388-394.


23. 23. Faraji, G., et al., The role of friction in tubular channel angular pressing. Rev. Adv. Mater. Sci, 31, 2012, pp. 12-18.


24. 24. Lin, J., et al., Study on deformation behavior and strain homogeneity during cyclic extrusion and compression. Journal of materials science, 43(21), 2008, pp. 6920-6924.