Study the Percentage of Carbon and Ferrite in Layers of Steel (SA-516) by Strip Cladding with E316L

Subject Areas :

Ahmad Afsari ¹ (Department of Mechanical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran)
Dara Fazel ² (Department of Mechanical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran)
Jafar Karimisharifabadi ³ (Department of Mechanical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran)
Vahid Mehrabi ⁴ (Department of Mechanical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran)

Received: 2020-06-14 Accepted : 2020-09-09 Published : 2020-08-01

Keywords:

References:

1] Chiu, K.Y., Cheng, F.T. and Man, H.C. 2006. Corrosion behavior of AISI 316L stainless steel surface-modified with NiTi. Surface and Coatings Technology. 200(20-21):6054-61.

[2] Vitanov, V.I., Javaid, N. and Stephenson, D.J. 2010. Application of response surface methodology for the optimization of micro friction surfacing process. Surface and Coatings Technology. 204(21-22):3501-3508.

[3] Khalid Rafi, H., Janaki Ram, G.D., Phanikumar and G., Rao, K.P. 2010. Microstructure and properties of friction surfaced stainless steel and tool steel coatings. Materials Science Forum. 638: 864-869.

[4] Amushahi, M.H., Ashrafizadeh, F. and Shamanian, M. 2010. Characterization of boride-rich hard facing on carbon steel by arc spray and GMAW processes. Surface and Coatings Technology. 204(16-17):2723-2728.

[5] Tabatabaeipour, S.M. and Honarvar, F. 2010. A comparative evaluation of ultrasonic testing of AISI 316L welds made by shielded metal arc welding and gas tungsten arc welding processes. Journal of materials processing technology. 210(8):1043-1050.

[6] Rafi, H.K., Ram, G.J., Phanikumar, G. and Rao, K.P. 2011. Microstructural evolution during friction surfacing of tool steel H13. Materials & Design. 32(1):82-87.

[7] Rajani, H.Z., Torkamani, H., Sharbati and M., Raygan, S. 2012. Corrosion resistance improvement in Gas Tungsten Arc Welded 316L stainless steel joints through controlled preheat treatment. Materials & Design. 34:51-57.

[8] Govardhan, D., Kumar, A.C., Murti, K.G and Reddy, G.M. 2012. Characterization of austenitic stainless steel friction surfaced deposit over low carbon steel. Materials & Design. 36:206-214.

[9] Puli, R. and Ram, G.J. 2012. Corrosion performance of AISI 316L friction surfaced coatings. Corrosion Science. 62:95-103.

[10] Dehaghi, E.M., Arezoodar, A.F. and Sattarifar, I. 2018. Numerical and Experimental Investigation of Layer Number Effect on Residual Stresses in Cladding Process. 49(4):295-298.

[11] Katsuyama, J., Nishikawa, H., Udagawa, M., Nakamura, M. and Onizawa, K. 2013. Assessment of residual stress due to overlay-welded cladding and structural integrity of a reactor pressure vessel. Journal of Pressure Vessel Technology. 135(5):051402.