Stabilized crack-opening stresses as a function of R-ratios and stress levels

محورهای موضوعی : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیک

Rahi Chermahini ¹ (Mobarakeh Steel Research Center, the core of fatigue and fracture in solids)
Majid Jabbari ² (Department of Mechanical Engineering., Khomeinishahr Branch, Islamic Azad University, Isfahan, 84175-119, Iran)

تاریخ دریافت : 1401/03/12 تاریخ پذیرش : 1401/03/31 تاریخ انتشار : 1400/12/10

کلید واژه: Finite Element, Cracks, Crack Closure, Elastic-plastic, Opening Stress,

چکیده مقاله :

An elastic-perfectly plastic middle crack tension aluminum 2024-T3 alloy was used under plane stress, plane strain and 3D analysis to determine stabilized crack-opening stresses for different R-ratios and stress levels. The stabilized crack-opening stresses of a 3D analysis locate between those values of plane stress and plane strain conditions. Using the above strategy, one can determine crack-opening stresses for any desired thickness value using interpolating scheme. Two and three dimensional programs were developed based on small strain elasticity theory incorporating linear strain isoparametric elements. The plasticity part of the analysis uses initial stress approach. The crack was extended one element size as the applied load reached the maximum value of each load cycle. Crack opening and closure stresses of nodes on the crack surface plane after some cyclic crack extensions are demonstrated. Based on the obtained results, for the three-dimensional finite-element analysis, the calculated stabilized crack opening stresses always locate between those of plane stress and plane strain conditions.

منابع و مأخذ:

 

[1] Newman, J. C. jr. (1998). The merging of fatigue and fracture mechanics concepts, a historical perspective. Progress in Aerospace science, 34, 347-390.

[2] Newman, J. C. jr and Raju, I.S. (1984). Stress intensity factor equation for crack in three –dimensional finite bodies subjected to tension and bending loads. NASA Technical Memorandum, 85793.

[3] Elber, W. (1968). Fatigue crack propagation. Ph.D. Thesis (University of New South Wales, Australia).

[4] Sih, G. C. and Chen, C. (1985). Non self-similar crack growth in elastic plastic –finite thickness plate. Theor  Appl  Fract. Mech, 3,125-139.

[5] Chermahini, R.G. (1986). Three-dimensional elastic-plastic finite element analysis of fatigue crack growth and closure. Ph.D.  Thesis (Old Dominion University, Norfolk, VA, August).

[6] Chermahini, R.G., Shivakumar, K.N. and Newman, J. C. jr. (1988). Three-dimensional finite-element simulation of fatigue crack growth and closure. ASTMSTP 982 (American society for Testing and materials).

[7] Chermahini, R.G., Shivakumar, K.N. and Newman, J. C. jr and Blom, A. F. (1989). Three-dimensional aspects of plasticity induced fatigue crack closure. Eng Frac Mech, 34, 393-401.

[8] Chermahini, R.G. and Blom, A.F. (1991). Variation of crack opening stresses in three-dimensional finite thickness plate. Theor Appl Fract Mech, 15, 267-276.

[9] Chermahini, R.G., Palmberg, B. and Blom, A.F. (1993). Fatigue crack growth and closure behavior of semicircular and elliptical surface flaws. Int J Fatigue, 4, 259-263.

[10] Chermahini, R.G. (2003). Fatigue crack growth and closure behavior of surface flaws under different R-ratios. Proceeding of the 4^th Iranian aerospace Society Conference, 87-98.

[11] Chermahini, R.G. (2004). Fatigue crack growth and closure behavior of circular and elliptical edge cracks. The Fifth national Conference of Iranian Aerospace Society, 325-329.

[12] Hossein Mirgilani, S.M. (2013). Modeling and crack-growth and calculate first intensity factor with ANSYS software. Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering, 2(4), 49-53.