Effects of Shielding Gas on the Mechanical and Microstructural Properties of 409L Ferritic Stainless Steels during Gas Metal Arc Welding

محورهای موضوعی : Journal of Environmental Friendly Materials

A. Feghhi ¹ (Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Isfahan, Iran.)
A. Emamikhah ² (Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Isfahan, Iran.)
Y. Bayat Asl ³ (Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Isfahan, Iran.)

تاریخ دریافت : 1396/06/09 تاریخ پذیرش : 1396/06/09 تاریخ انتشار : 1396/06/10

کلید واژه:

چکیده مقاله :

The present study investigates the effects of type of shielding gas on the weld microstructure and mechanical properties of 409L ferritic stainless steel. For this purpose, Ar, Ar +20% He, Ar + 12% CO2, and Ar + 25% CO2 were used as shielding gases in gas metal arc welding (GMAW) of stainless steel. To evaluate the welds, non-destructive inspections of the specimens were followed by mechanical (hardness and tensile) tests while microstructural examinations of both the heat affected zone (HAZ) and the fusion zone were performed. Moreover, the phases produced were observed and identified by analyzing the specimens using SEM and EDS techniques. Results showed that specimens welded with Ar + 25% CO2 and Ar + 12% CO2 have the highest strength and hardness values in the fusion zone due to the formation of martensite around the ferrite grains. However, the enhancements observed in the mechanical properties of specimens welded with Ar and Ar +20% He were attributed to the reduced ferrite grain size and martensite content

منابع و مأخذ:

[1] T. Varga, T. Konkoly and H. Straube: Investigation on microstructure, toughness, and defect tolerance of gas metal arc weld metal, IIW. Doc., X-1205-90, (1990).

[2] P. Kah, R. Suoranta and J. Martikainen. Int. J. Adv. Manuf. Technol., 67(2013), 655.   

[3] B. Mvola, P. Kah, J. Martikainen, and R. Suoranta, J. Eng. Manu. Part B., 229(2015), 1694.

[4] ASM handbook. Welding, brazing, and soldering, ASM, Cleveland, (1993).

[5] S.W. Campbell, F.H. Ley, A.M. Galloway and N. McPherson, J. Eng. Manu. Part B., 229(2015), 122.

[6] C. Kim,  J. Eng. Manu. Part B., 229(2015), 1557. 

[7] S. Mukhopadhyay, T. K. Pal, Int. J. Adv. Manuf. Technol., 29(2005), 262.

[8] V. V. Vaidya, Weld. J., 81(2002), 43.

[9] S. Lathhabai, R. D. Stout, Weld. J., 64(1985), 303.

[10] M. Dreher, S. Fussel, S. Rose, M. Habler, M. Hertel and M. Schnick, Int. J. Adv. Manuf. Technol. 57(2013), 391.

[11] R. C. Cochrane, P. R. Kirkwood, In Proc of the Int Conf on Trends in Steel and Consumables for Welding, the Welding Institute, London, (1978), 103.

[12] L. Pires, L. Quintino and R. M. Miranda, Mater. Des., 28(2007), 1623.

[13] C. J. Niekerk, M. Toit and M. W. Erwee, Welding in the World, 56(2012), 54.

[14] AWS Welding handbook. Stainless steels. (1997), 4.

[15] Y. Uematsu, N. Hiramatsu and M. Oku, US5462611 A 1995. International Patent Application No. US/08356, 248.

[16] V. Kuzucu, M. Aksoy, M. H. Korkut and M.M.Yildirim, Mater. Sci. Eng. A, 230(1997), 75.

[17] R. T. J. Hodges, j. Corros. Sci. Eng., 27(1971), 119.

[18] H. K. D. H. Behadeshia. Mater. Sci. Forum., 539-543(2007), 6.

[19] A. Miyazaki, M. Gunzi and K. Yoshioka, Kawasaki. Steel. Tech. Rep., 15(1994), 21.

[20] B. W. Ahn, D. H. Choi, D. J. Kim, S.B. Jung, Mater. Sci. Eng. A, 532(2012), 476.

[21] D. A. Brandt, J. C. Warner: Metallurgy Fundamentals, 5th Edition, Goodheart-Willcox Publisher, (2009).  

[22] Standard test Method for Tension Testing of Metallic Materials (1998) ASTM E 8M Annual Book of ASTM Standards, Part 8; ASTM.

[23] F. Mohammadi, F. Eliyan and A. Alfantazi, Corros. Sci., 63(2012), 323.

[24] H. Y. Liou, R. L. Hsieh and W. T. Tsai, Corros. Sci., 44(2002(, 2841.

[25] S. Kumar, A. S. Shahi, Mater. Des., 32(2011), 3617.

[26] Z. H. Rao, S. M. Liao and H. L. Tsai, J. Appl. Phys., 107(2010), 044902. 

[27] J. C. Lippold, D. J. Kotecki: Welding metallurgy and weldability of stainless steels. Wily publications, (2005).

[28] A. K. Lakshminarayanan, V. Balasubramanian, Mater. Des., 31(2010), 4592.

[29] C. L. Briant, S. K. Banerji, Int. Mater. Rev., 23(1978) 164.

[30] A. J. Sedriks: Corrosion of stainless steels. Wily Publications, (1996).

[31] J. K. Kim, Y. H. Kim, S. H. Uhm, J. S. Lee, and K. Y. Kim, Corros. Sci., 51(2009), 2716.