Micro Electropolishing of the MEMS Metallic Structures Fabricated by the Micro WEDM Process

محورهای موضوعی : meso/micro/nano fabrication

Mohammad Tahmasebipour ¹ (Faculty of New sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran Micro/Nanofabrication Technologies Lab, Faculty of New Sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran)
Younes Tahmasebipour ² (Micro/Nanofabrication Technologies Lab, Faculty of New Sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran)
Mahya Boujari Aliabadi ³ (Faculty of New sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran Micro/Nanofabrication Technologies Lab, Faculty of New Sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran)
Shadi Ebrahimi ⁴ (Faculty of New sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran Micro/Nanofabrication Technologies Lab, Faculty of New Sciences and Technologies, University of Tehran, Tehran, 14395 -1561, Iran)

تاریخ دریافت : 1400/02/02 تاریخ پذیرش : 1400/05/23 تاریخ انتشار : 1400/12/10

کلید واژه: micro WEDM, wire electrical discharge machining, MEMS, micro electropolishing, micro polishing, Microelectromechanical Systems,

چکیده مقاله :

In this study, the micro electro-polishing method was employed to improve the surface quality of microbeams machined by the micro WEDM method and to remove the recast layer. This approach changes the dimensions of the microbeams, as a result of the electrochemical corrosion, in addition to the elimination of the recast layer. To diminish the impact of this process on the dimensional deviation of the fabricated microbeams, the influence of the micro electro-polishing process parameters such as voltage, duration, cathode diameter, and electrolyte composition on the dimensional deviation of microbeams was studied using the Taguchi method. The optimum values of process parameters were determined by the S/N ratios analysis, and the order of parameters importance was determined through analysis of variance of the S/N ratios. It was found that the optimal levels of the process parameters are voltage of 2 V, process duration of 20 s, cathode diameter of 50 mm, and electrolyte composition of 25-5-40 ml (sulfuric-phosphoric-water) within the range of experiments. By using the optimum values of the parameters, the dimensional deviations were found to be 5.23 times lower compared to the average of the results. The importance of process parameters was found to follow this order: electropolishing duration, electrolyte composition, cathode diameter, and process voltage.

منابع و مأخذ:

• Saleh, T., Rasheed, A. N., and Muthalif, A. G., Experimental Study On Improving μ-WEDM and μ-EDM of Doped Silicon by Temporary Metallic Coating, The International Journal of Advanced Manufacturing, Vol. 78, No. 9, 2015, pp. 1651-1663, https://doi.org/10.1007/s00170-014-6732-4.


• Tahmasebipour, M., Design, Performance and Modeling of Nano Electrical Discharge Machining Process, Ph.D. Dissertation, Tarbiat Modares University, Iran, 2009.


• Tahmasebipour, Y., Ghoreishi, M., and Tahmasebipour, M., Finite-Volume Heat Transfer Model of the Nano Electrical Discharge Machining Process, Journal of Nanoelectronics and Optoelectronics, 9, 2014, pp. 605-611, https://doi.org/10.1166/jno.2014.1641.


• Tahmasebipour, G., Ghoreishi, M., and Tahmasebipour, Y., Computational Fluid Dynamic Simulation of the Nanoelectrical Discharge Machining Process, NANO, No. 6, 2011, pp. 561-568, https://doi.org/10.1142/S1793292011002950.


• Tahmasebipour, G., Tahmasebipour, Y., and Ghoreishi M., Electro-Spark Nanomachining Process Simulation. International Journal of Materials, Mechanics and Manufacturing, Vol. 2, No. 1, 2014, pp. 32-35. DOI: 10.7763/IJMMM.2014.V2.94.


• Tahmasebipour, G., Tahmasebipour, Y., and Ghoreishi, M., Thermal Model of the Electro-Spark NanoMachining Process, International Journal of Materials, Mechanics and Manufacturing, 2, No. 1, 2014, pp. 56-59, DOI: 10.7763/IJMMM.2014.V2.99.


• Fonda, P., Nakamoto, K., Heidari, A., Yang, H. A., Horsley, D. A., and Lin, L., A Study On the Optimal Fabrication Method for Micro Scale Gyroscopes Using a Hybrid Process Consisting of Electric Discharge Machining, Chemical Etching or Micro Mechanical Milling, CIRP Ann. Manuf. Technol, Vol. 62. No. 1, 2013, pp. 186-186, https://doi.org/10.1016/j.cirp.2013.03.035.


• Fonda, P., Chan, M. L., Heidari, A., Nakamoto, K., Sano, S., Horsley, D. D., and Yamazaki, K., The Application of Diamond-based Electrodes for Efficient EDMing of Silicon Wafers for Freeform MEMS Device Fabrication, Procedia CIRP, Vol. 6, 2013, pp. 280-285, https://doi.org/10.1016/j.procir.2013.03.020.


• Yan, B. H., Wang, A. C., Huang, C. Y., and Huang, F. Y., Study of Precision Micro Holes In Borosilicate Glass Using Micro EDM Combined with Micro Ultrasonic Vibration Machining, Int. J. of Mach. Tool and Manuf, Vol. 42, No. 10, 2002, pp. 1105-1112, https://doi.org/10.1016/S0890-6955(02)00061-5.


• Saleh, T., Dahmardeh, M., Bsoul, A., Nojeh, A., and Takahata, K., High-Precision Dry Micro Electro-Discharge Machining of Carbon-Nanotube Forests With Ultralow Discharge Energy, Micro Electro Mechanical Systems (MEMS), 2012 IEEE 25th International Conference on, 15 March 2012, Paris, France, DOI: 10.1109/MEMSYS.2012.6170140.


• Ali, M. Y., Mohammad, A. S., Effect of Conventional EDM Parameters On the Micromachined Surface Roughness and Fabrication of a Hot Embossing Master Microtool, Mat and Manuf Process, Vol. 24, No. 4, 2009, pp. 454-458, https://doi.org/10.1080/10426910802714373.


• Saxena, K. K., Srivastava, A. S., and Agarwal, S., Experimental Investigation into the Micro Edm Characteristics of Conductive SiC, Ceram. Int, Vol. 42, No. 1, 2016, pp. 1597-1610, https://doi.org/10.1016/j.ceramint.2015.09.111.


• Ali, M. Y., Karim, A. M., Adesta, E. Y., Ismail, A. F., Abdullah, A. A., and Idris, M. N., Comparative Study of Conventional and Micro Wedm Based on Machining of Meso/Micro Sized Spur Gear, Int. J. of Precis. Eng. and Manuf, Vol. 11, No. 5, 2010, pp. 779-784, https://doi.org/10.1007/s12541-010-0092-2.


• Vafaie, A., Tahmasebipour, M., and Tahmasebipour, Y., A novel capacitive micro accelerometer made of Steel using Micro Wire Electrical Discharge Machining Method, Journal of Micromechanics and Microengineering, Vol. 29, No.12, 2019, pp. 125018, https://doi.org/10.1088/1361-6439/ab4e41.


• Tahmasebipour, M., Vafaie, A., A Novel Single Axis Capacitive Mems Accelerometer with Double-Sided Suspension Beams Fabricated Using μWEDM, Sensors and Actuators A: Physical, Vol. 309, 2020, pp. 112003, https://doi.org/10.1016/j.sna.2020.112003.


• Tahmasebipour, M., Sangchap, M., A Novel High Performance Integrated Two-Axis Inchworm Piezoelectric Motor, Smart Materials and Structures, Vol. 29. No. 1, 2020, pp. 015034, https://doi.org/10.1088/1361-665X/ab545e.


• Sangchap, M., Tahmasebipour, M., and Tahmasebipour, Y., A Linear Inchworm Piezomotor with a New Configuration: Design Considerations, Fabrication and Characterization. Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, 2020, pp. 1-12, https://doi.org/10.1007/s40997-020-00409-x.


• Mahmoud, S., Al-Dadah, R., Aspinwall, D. K., Soo, S. L., and Hemida, H., Effect of Micro Fin Geometry On Natural Convection Heat Transfer of Horizontal Microstructures, Appl. Therm. Eng, Vol. 31, No. 5, 2011, pp. 627-633, https://doi.org/10.1016/j.applthermaleng.2010.09.017.


• Zubir, M. N., Shirinzadeh, B., Development of a Novel Flexure Based Microgripper for Precision Manipulation of Micro Objects, Industrial Technology Conference, 2009. ICIT2009. IEEE International Conference on, 10-13 Feb. 2009, Gippsland, VIC, Australia, DOI: 10.1109/ICIT.2009.4939527.


• Du, L. Q., Wang A. A., Zhao M., and Song M. C., The Fabrication of Trans-Scale Micro Fuze Safety Device, Key Eng. Mat, Vol. 609, 2014, pp. 769-800, https://doi.org/10.4028/www.scientific.net/KEM.609-610.796.


• Liao, Y. S., Chen, S. T., Lin, C. S., and Chuang, T. J., Fabrication of High Aspect Ratio Microstructure Arrays by Micro Reverse Wire-EDM, J. of Micromech. And Microeng, Vol. 15, No. 8, 2005, pp. 1547, https://doi.org/10.1088/0960-1317/15/8/024.


• Song, M. C., Du, L. Q., Liu, C., Liu, J. S., and Liu, Y., Experimental Research on WEDM Machining for Metal Components with Micro/Meso-Scale, Key Eng. Mat, Vol. 609, 2014, pp. 1521-1525, https://doi.org/10.4028/www.scientific.net/KEM.609-610.1521.


• Schoth, A., Forster, R., and Menz, W., Micro Wire EDM for High Aspect Ratio 3D Microstructuring of Ceramics and Metals, Microsyst. Technol, Vol. 11, No. 4, 2005, pp. 250-253, https://doi.org/10.1007/s00542-004-0399-y.


• Tahmasebipour, M., Tahmasebipour, Y., and Vafaie, A., Micro Wire Electrical Discharge Machining of the MEMS Structures with Optimized Dimensional Deviation, Int. J. Adv. Des. Manuf. Technol, Vol. 12, No. 2, 2019, pp. 103.


• Zhenlong, W., Xuesong, G., Guanxin, C., and Yukui, W., Surface Integrity Associated with SiC/Al Particulate Composite by Micro Wire Electrical Discharge Machining, Mat. And Manuf. Process, Vol. 29, No. 5, 2014, pp. 532-539, https://doi.org/10.1080/10426914.2014.901520.


• Tahmasebipour, M., Tahmasebipour, Y., Shabani, A. A., and Boujari, M., Effect of Micro Wire-EDM Process Parameters on Recast Layer in the Molybdenum Micromachining, Int. J. Adv. Des. Manuf. Technol, Vol. 10, No. 1, 2017, pp. 101.


• Tahmasebipour, G., Hojjat, Y., Ahmadi, V., and Abdullah, A., Optimization of STM/FIM Nanotip Aspect Ratio Based On the Taguchi Method, The International Journal of Advanced Manufacturing Technology, Vol. 44, No. 1, 2009, pp.80-90, https://doi.org/10.1007/s00170-008-1799-4.


• Tahmasebipour, G., Hojjat, Y., Ahmadi, V., and Abdullah, A., Effect of Fabrication Process Parameters On the Apex‐Radius of STM Tungsten Nanotip, Scanning: The Journal of Scanning Microscopies, Vol. 31, No. 2, 2009, pp.65-74, https://doi.org/10.1002/sca.20142.


• Tahmasebipour, G., Ahmadi, V., Abdullah, A., and Hojjat, Y., Fabrication of STM Tungsten Nanotip by Electrochemical Etching Method, International Journal of Nanoscience, Vol. 8, No. 03, 2009, pp. 305-310, https://doi.org/10.1142/S0219581X09006110.


• Tahmasebipour, G., Ahmadi, V., and Abdullah, A., Optimization of Electrochemical Etching Parameters in FIM/STM Tungsten Nanotip Fabrication, Journal of Sciences, Islamic Republic of Iran, Vol. 21, No. 1, 2010, pp. 75-8