Fatigue Life of Graphite Powder Mixing Electrical Discharge Machining AISI D2 Tool Steel
محورهای موضوعی : EngineeringA Al-Khazraji 1 , S.A Amin 2 , S.M Ali 3
1 - Mechanical Engineering Department, University of Technology, Baghdad, Iraq
2 - Mechanical Engineering Department, University of Technology, Baghdad, Iraq
3 - Biomedical Engineering Department, University of Technology, Baghdad, Iraq
کلید واژه: FEM, Fatigue Life, RSM, ANOVA, EDM, PMEDM, Graphite powder, AISI D2 Die Steel, WLT, Total heat flux, Fatigue safety factors,
چکیده مقاله :
The present paper deals with the design of experimental work matrices for two groups of experiments by using Response surface methodology (RSM). The first EDM group was dealt with the use of kerosene dielectric alone, while the second was treated by adding the graphite micro powders mixing to dielectric fluid (PMEDM). The total heat flux generated and fatigue lives after EDM and PMEDM models were developed by FEM using ANSYS 15.0 software. The graphite electrodes gave a total heat flux higher than copper electrodes by (82.4 %). The use of graphite powder and both electrodes yielded more heat flux by (270.1 %) and (102.9 %) than the copper and graphite electrodes, respectively with use of kerosene dielectric alone. Using graphite electrodes and kerosene dielectric alone improved the WLT by (40.0 %) when compared with the use of copper electrodes. Whereas, using copper electrodes and the graphite powder improved the WLT by (66.7 %) compared with the use of graphite electrodes under the same machining conditions. Copper electrodes with graphite powder gave experimental fatigue safety factor higher by (30.38 %) when compared with using graphite electrodes and higher by (15.73%) and (19.77%) when compared with using the copper and graphite electrodes and kerosene dielectric alone, respectively.
[1] Lee L.C., Lim L.C., Wong Y.S., Lu H.H., 1990, Towards a better understanding of the surface features of electro-discharge machined tool steels, The Journal of Materials Processing Technology 24: 513-523.
[2] Lim L.C., Lee L.C., Wong Y.S., Lu H.H. 1991, Solidification microstructure of electro discharge machined surfaces of tool steels, Journal of Materials Science and Technology 7: 239-248.
[3] Lin Y.C., Yan B.H., Huang F.Y., 2001, Surface improvement using a combination of electrical discharge machining with ball burnish machining based on the Taguchi method, The International Journal of Advanced Manufacturing Technology 18(9): 673-682.
[4] Abu Zeid O.A., Ho K.H., Newman S.T., 2003, On the effect of electro-discharge machining, International Journal of Machine Tools & Manufacture 43: 1287-1300.
[5] Khundrakpam N.S., Singh H., Kumar S., Brar G.S., 2014, Investigation and modeling of silicon powder mixed EDM using response surface method, International Journal of Current Engineering and Technology 4(2): 1022-1026.
[6] Reddy B., Kumar G.N., Chandrashekar K., 2014, Experimental investigation on process performance of powder mixed electric discharge machining of AISI D3 steel and EN-31 steel, International Journal of Current Engineering and Technology 4(3): 1218-1222.
[7] ASTM A370, Standard Test Method and Definitions for Mechanical Testing of Steel Products, American Society for Testing and Materials, Washington.
[8] ASTM A681, Standard Specification for Tool Steels Alloy, American Society for Testing and Materials, Washington.
[9] Bhattacharya R., Jain V.K., Ghoshdastidar P.S., 1996, Numerical simulation of thermal erosion in EDM process, Journal of the Institution of Engineers Part PR, Production Engineering Division 77: 13-19.
[10] Yadav V., Jain V.K., Dixit P.M., 2002, Thermal stresses due to electrical discharge machining, International Journal of Machine Tools and Manufacture 42: 877-888.
[11] Patel B.B., Rathod K.B., 2012, Multi-parameter analysis and modeling of surface roughness in electro cischarge machining of AISI D2 steel, International Journal of Scientific & Engineering Research 3(6): 1-6.
[12] Shankar P., Jain V.K., Sundarajan T., 1997, Analysis of spark profiles during EDM process, Machining Science Technology 1(2): 195-217.
[13] Marafona J., Chousal J.A., 2006, A finite element model of EDM based on the Joule effect, International Journal of Machine Tools and Manufacture 46: 595-602.
[14] Shigley J.E., Mischke C.R., 2006, Mechanical Engineering Design, McGraw-Hill Inc.
