Modal Testing and Finite Element Analysis of Crack Effects on Turbine Blades
محورهای موضوعی : EngineeringK.R.P Babu 1 , B.R Kumar 2 , K.M Rao 3
1 - Research Scholar, Department of Mechanical Engineering, JNTUK Kakinada, India----
Department of Mechanical Engineering, KLEF University, Guntur, India
2 - Department of Mechanical Engineering, KLEF University, Guntur, India
3 - Department of Mechanical Engineering, JNTUK Kakinada, India
کلید واژه: Finite Element Analysis, Turbine blade, Vibration response, Twisted cantilever beam, FFT analyzer,
چکیده مقاله :
The study of vibration response of a turbine blade helps to detect the crack presence in the blade which alters its dynamic characteristics. The change is characterized by changes in the modal parameters associated with natural frequencies. In this paper, study of vibration response is made for turbine blade in the presence of a crack like defect. Turbine blade is initially assumed as a cantilever beam. Modal testing has been carried out for both the beams with different crack depth and crack location ratios using FFT spectrum analyzer and ANSYS software. From the analysis, it has been observed that the crack depth and its location have noticeable effect on the natural frequencies. Later the same cantilever beam was twisted with different angle of twists to validate the cantilever beam model to turbine blade.
[1] Dimarogonas A.D., 1970, Dynamic Response of Cracked Rotors, General Electric Co., Internal Report, NY, USA.
[2] Dimarogonas A.D., 1971, Dynamics of Cracked Shaft, General Electric Co., Internal Report, NY, USA.
[3] Wendtland D., 1972, Anderung der biegeeigen frequenzen einer idealisierten schaufel durch rise, Thesis, University of Karlsruhe.
[4] Adams R.D., Cawley P., Pye C.J., Stone B.J., 1978, A vibration technique for non-destructively assessing the integrity of structures, Journal of Mechanical Engineering Science 20: 93-100.
[5] Cawley P., Adams R.D., 1979, The location of defects in structures from measurements of natural frequencies, Journal of Strain Analysis 14: 49-57.
[6] Chondros T.G., Dimarogonas A.D., 1980, Identification of cracks in welded joints of complex structures, Journal of Sound and Vibration 69: 531-538.
[7] Dimarogonas A.D., Massouros G., 1980, Torsional vibration of a shaft with a circumferential crack, Engineering Fracture Mechanics 15: 439-444.
[8] Gudmundson P., 1982, Eigenfrequency changes of structures due to crack, notches or other geometrical changes, Journal of the Mechanics and Physics of Solids 30: 339-53.
[9] Dimarogonas A.D, Papadopoulos C.A., 1983, Vibration of cracked shaft in bending, Journal of Sound and Vibration 91: 583-593.
[10] Anifantis N., Aspragathos N., Dimarogonas A.D., 1983, Diagnosis of cracks on concrete frames due to earthquakes by vibration response analysis, 3rd International Symposium of International Measurements Federation (IMEKO), Moscow.
[11] Dentsoras A.J., Dimarogonas A.D., 1983, Resonance controlled fatigue crack propagation in a beam under longitudinal vibrations, International Journal of Fracture 23: 15-22.
[12] Sato H., 1983, Free vibration of beams with abrupt changes of cross-section, Journal of Sound and Vibration 89: 59-64.
[13] Nahvi H., Jabbari M., 2005, Crack detection in beams using experimental modal data and finite element model, International Journal of Mechanical Science 47: 1477-1497.
[14] Lele S.P., Maiti S.K., 2002, Modeling of transverse vibration of short beams for crack detection and measurement of crack extension, Journal of Sound and Vibration 257: 559-583.
[15] Babu K.R.P., Prasad G.D., 2012, Crack detection in beams from the differences in curvature mode shapes, Journal of Structural Engineering India 39(2): 237-242.
