Effect of Fluoride Coating on the Degradation of Mg-Based Alloy Containing Calcium for Biomedical Applications

محورهای موضوعی : Bio Materials

Abouzar Rezaei-Baravati ¹ , Masoud Kasiri-Asgarani ² , Hamid Reza Bakhsheshi-Rad ³ , Mahdi Omidi ⁴ , Ebrahim Karamian ⁵

1 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
2 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
3 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
4 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
5 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran

تاریخ دریافت : 1400/08/05 تاریخ پذیرش : 1400/10/08 تاریخ انتشار : 1400/10/11

کلید واژه: Magnesium alloy, Corrosion behavior, Surface Treatment, Biocompatibility, Fluoride treatment,

چکیده مقاله :

The effect of hydrofluoric acid (HF) treatment on the corrosion performance of the Mg–Zn–Al–0.5Ca alloy was studied by immersing a specimen in HF solutions for varying lengths of time at room temperature. X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the evolution of microstructures. In vitro corrosion resistance was assessed using potentiodynamic polarization and a room-temperature immersion test in Kokubo solution. The fluoride-treated Mg–Zn–Al–0.5Ca alloy formed by 24h immersion in HF exhibited a more homogeneous, compact, and thicker (2.1 μm) coating layer compared to the other HF treated specimens in 6, 12 and 18 hours. The corrosion resistance performance of the Mg–Zn–Al–0.5Ca alloy formed by 24h immersion in HF was the best, with a corrosion rate of 2.87 mm/y according to the electrochemical experiment. The mean weight loss of the untreated samples was more considerably higher (up to 2 times) than that of the fluoride-treated alloys, according to in vitro degradation assessments. According to the findings because of its low degradation kinetics and apatite formation ability, the fluoride-treated Mg–Zn–Al–0.5Ca alloy is a promising candidate for biodegradable implants.

منابع و مأخذ:

[1] C. Zhang, S. Zhang, D. Sun, J. Lin, F. Meng, H. Liu, "Superhydrophobic fluoride conversion coating on bioresorbable magnesium alloy–fabrication, characterization, degradation and cytocompatibility with bmscs", J. Magnesium Alloys, Vol. 9, No. 4, 2021, pp. 1246-1260.

[2] S. Ghaedi Faramoushjani, F. Chinaei, H.R. Bakhsheshi-Rad, M. Hasbullah Idris, "Effect of fluoride conversion coating on corrosion of behavior of mg-ca-zn alloy", Proc. Advanced Materials Research, 2013, pp. 3-6.

[3] I. Baghni, Y.-S. Wu, J.-Q. Li, C. Du, W. Zhang, "Mechanical properties and potential applications of magnesium alloys", Trans. Nonferrous Met. Soc. China, Vol. 13, No. 6, 2003, pp. 1253-1259.

[4] Z.-Z. Yin, W.-C. Qi, R.-C. Zeng, X.-B. Chen, C.-D. Gu, S.-K. Guan, Y.-F. Zheng, "Advances in coatings on biodegradable magnesium alloys", J. Magnesium Alloys, Vol. 8, No. 1, 2020, pp. 42-65.

[5] X. Xiong, Y. Yang, J. Li, M. Li, J. Peng, C. Wen, X. Peng, "Research on the microstructure and properties of a multi-pass friction stir processed 6061al coating for AZ31 Mg alloy", J. Magnesium Alloys, Vol. 7, No. 4, 2019, pp. 696-706.

[6] Y. Guo, Y. Zhang, Z. Li, S. Wei, T. Zhang, L. Yang, S. Liu, "Microstructure and properties of in-situ synthesized ZrC-Al3Zr reinforced composite coating on AZ91D magnesium alloy by laser cladding", Surf. Coat. Technol., Vol. 334, 2018, pp. 471-478.

[7] X.-B. Chen, H.-Y. Yang, T.B. Abbott, M.A. Easton, N. Birbilis, "Corrosion protection of magnesium and its alloys by metal phosphate conversion coatings", Surf. Eng., Vol. 30, No. 12, 2014, pp. 871-879.

[8] S. Li, L. Yi, X. Zhu, T. Liu, "Ultrasonic treatment induced fluoride conversion coating without pores for high corrosion resistance of Mg alloy", Coatings, Vol. 10, No. 10, 2020, pp. 996.

[9] T. Yan, L. Tan, D. Xiong, X. Liu, B. Zhang, K. Yang, "Fluoride treatment and in vitro corrosion behavior of an AZ31B magnesium alloy", Mater. Sci. Eng., C, Vol. 30, No. 5, 2010, pp. 740-748.

[10] F. Witte, J. Fischer, J. Nellesen, C. Vogt, J. Vogt, T. Donath, F. Beckmann, "In vivo corrosion and corrosion protection of magnesium alloy LAE442", Acta Biomater., Vol. 6, No. 5, 2010, pp. 1792-1799.

[11] Y. Chen, Y. Song, S. Zhang, J. Li, H. Wang, C. Zhao, X. Zhang, "Effect of fluoride coating on in vitro dynamic degradation of Mg–Zn alloy", Mater. Lett., Vol. 65, No. 17-18, 2011, pp. 2568-2571.

[12] M. Ren, S. Cai, T. Liu, K. Huang, X. Wang, H. Zhao, S. Niu, R. Zhang, X. Wu, "Calcium phosphate glass/MgF₂ double layered composite coating for improving the corrosion resistance of magnesium alloy", J. Alloys Compd., Vol. 591, 2014, pp. 34-40.

[13] T. Kokubo, H. Takadama, How useful is SBF in predicting in vivo bone bioactivity?,  Biomaterials Vol. 27, 2006, pp. 2907–2915. 

[14] C. Zhang, C. Liu, Y. Ma, "Preparation of compound coating of fluorine conversion layer and calcium phosphate on AZ31 magnesium alloy", Mater. Res. Innovations, Vol. 18, No. sup2, 2014, pp. S2-564-S2-569.

[15] J. Yang, J. Peng, E.A. Nyberg, F.-s. Pan, "Effect of Ca addition on the corrosion behavior of Mg–Al–Mn alloy", Appl. Surf. Sci., Vol. 369, 2016, pp. 92-100.

[16] S.Z. Khalajabadi, M.R.A. Kadir, S. Izman, R. Ebrahimi-Kahrizsangi, "Fabrication, bio-corrosion behavior and mechanical properties of a mg/ha/mgo nanocomposite for biomedical applications", Mater. Des., Vol. 88, 2015, pp. 1223-1233.

[17] E. Budke, J. Krempel-Hesse, H. Maidhof, H. Schüssler, "Decorative hard coatings with improved corrosion resistance", Surf. Coat. Technol., Vol. 112, No. 1-3, 1999, pp. 108-113.

[18] Y. Wan, G. Xiong, H. Luo, F. He, Y. Huang, X. Zhou, "Preparation and characterization of a new biomedical magnesium–calcium alloy", Mater. Des., Vol. 29, No. 10, 2008, pp. 2034-2037.

[19] X. Gu, W. Zheng, Y. Cheng, Y. Zheng, "A study on alkaline heat treated Mg–Ca alloy for the control of the biocorrosion rate", Acta Biomater., Vol. 5, No. 7, 2009, pp. 2790-2799.

[20] B.-L. Yu, J.-K. Lin, J.-Y. Uan, "Applications of carbonic acid solution for developing conversion coatings on Mg alloy", Trans. Nonferrous Met. Soc. China, Vol. 20, No. 7, 2010, pp. 1331-1339.

[21] X. Gu, N. Li, W. Zhou, Y. Zheng, X. Zhao, Q. Cai, L. Ruan, "Corrosion resistance and surface biocompatibility of a microarc oxidation coating on a Mg–Ca alloy", Acta Biomater., Vol. 7, No. 4, 2011, pp. 1880-1889.

[22] H.R. Bakhsheshi-Rad, M.H. Idris, M.R.A. Kadir, M. Daroonparvar, "Effect of fluoride treatment on corrosion behavior of Mg–Ca binary alloy for implant application", Trans. Nonferrous Met. Soc. China, Vol. 23, No. 3, 2013, pp. 699-710.