List of Articles Discharge Machining Open Access Article Abstract Page Full-Text 1 - Effect of the Micro Wire-EDM Process Parameters on the Recast Layer in the Molybdenum Micromachining Mohammad Tahmasebipour Y. Tahmasebipour A. Shabani M. Boujari Aliabadi Open Access Article Abstract Page Full-Text 2 - Micro Wire Electrical Discharge Machining of MEMS Structures with Optimized Dimensional Deviation Mohammad Tahmasebipour Younes Tahmasebipour Ali Vafaie Open Access Article Abstract Page Full-Text 3 - Investigation of the TiO2/SiC/SiO2 Coating Effect On the Wear Rate of Needle Graphite Electrode by using Electrical Discharge Machining Hossein Alian Moghadam majid jabbari Saeed Daneshmand Saeid Rasouli Jazi Arezoo Khosravi 10.30495/admt.2021.1923176.1251 Open Access Article Abstract Page Full-Text 4 - Micro Electropolishing of the MEMS Metallic Structures Fabricated by the Micro WEDM Process Mohammad Tahmasebipour Younes Tahmasebipour Mahya Boujari Aliabadi Shadi Ebrahimi 10.30486/admt.2022.1928592.1277 Open Access Article Abstract Page Full-Text 5 - Using design of experiments approach and simulated annealing algorithm for modeling and Optimization of EDM process parameters Masoud Azadi Moghaddam Farhad Kolahan Meysam Beytolamani Open Access Article Abstract Page Full-Text 6 - Investigation of Parameters Affecting Surface Integrity and Material Removal during Electrical Discharge Machining of HARDOX-400 Steel Hesam Motevasseli Ahmad Afsari Ali Khosravifard Open Access Article Abstract Page Full-Text 7 - Investigation of the Impact of the Alumina Powder Presence in Dielectric on Electrical Discharge Machining Parameters of A413 Aluminum Workpiece using Taguchi's Experiment Design, Signal-to-noise Analysis, and Total Normalized Quality Loss Mojtaba Shahbazi Dastjerdi Ali Mokhtarian Mojtaba Rahimi Open Access Article Abstract Page Full-Text 8 - Experimental Investigation of the Effect of Deionized Water on Surface Roughness of Near Dry Electro Discharge Machining of AISI D2 Steel Mojtaba Taghizadeh Sayed Ali Mosavi Open Access Article Abstract Page Full-Text 9 - Intelligent Knowledge Based System Approach for Optimization of Design and Manufacturing Process for Wire-Electrical Discharge Machining Morteza Sadegh Amalnik Open Access Article Abstract Page Full-Text 10 - An experimental analysis and optimization of machining rate and surface characteristics in WEDM of Monel-400 using RSM and desirability approach Vinod Kumar Vikas Kumar Kamal Kumar Jangra Open Access Article Abstract Page Full-Text 11 - Multi-objective optimization in WEDM of D3 tool steel using integrated approach of Taguchi method & Grey relational analysis Anand S. Shivade Vasudev D. Shinde Open Access Article Abstract Page Full-Text 12 - The Effect of Electrical Discharge Machining Parameters On 2024 Aluminum-Based Composite Material Using Calculation and Analysis of the Total Normalized Quality Loss and Signal-to-Noise Analysis Behnam Masoudi saeed daneshmand Open Access Article Abstract Page Full-Text 13 - Electrical Discharge Machining of Aluminum Matrix Composite Reinforced With Titanium Oxide Nano-Particles Ali akbar lotfi Saeed Daneshmand Open Access Article Abstract Page Full-Text 14 - Investigation and Optimization of the Effect of Input Parameters on Material Removal Rate, Tool Wear Rate, and Surface Roughness in Electrical Discharge Machining of A356 Nano-Composite Reinforced By Alumina Mohammad Javad HajHosseini Ali Mokhtarian Mojtaba Rahimi Behnam Masoudi Open Access Article Abstract Page Full-Text 15 - Study of the effect of magnetic field on the surface roughness of the workpiece in electric discharge machining of Al2O3-reinforced A413 composite Ahmadreza Mizbani Sayed Ehsan Mirmohammadsadeghi Ali Mokhtarian Open Access Article Abstract Page Full-Text 16 - Investigation and optimization of the effect of input parameters on output parameters of electrical discharge machining of A356 nano-composite reinforced by SiC Amir Rahmani Ali Mokhtarian Mojtaba Rahimi Open Access Article Abstract Page Full-Text 17 - بهینهسازی نرخ براده برداری در ماشینکاری تخلیه الکتریکی بر روی آلیاژ DIN 1.2080 با کمک روش شبکه عصبی و الگوریتم ژنتیک مسعود عظیمی امین کلاه دوز سید علی افتخاری
