List of Articles Electrical discharge machining

• Open Access Article
  • Abstract Page
  • Full-Text
  
  1 - Effect of the Micro Wire-EDM Process Parameters on the Recast Layer in the Molybdenum Micromachining
  Mohammad Tahmasebipour Y. Tahmasebipour A. Shabani M. Boujari Aliabadi
• Open Access Article
  • Abstract Page
  • Full-Text
  
  2 - Micro Wire Electrical Discharge Machining of MEMS Structures with Optimized Dimensional Deviation
  Mohammad Tahmasebipour Younes Tahmasebipour Ali Vafaie
• Open Access Article
  • Abstract Page
  • Full-Text
  
  3 - Investigation of the TiO2/SiC/SiO2 Coating Effect On the Wear Rate of Needle Graphite Electrode by using Electrical Discharge Machining
  Hossein Alian Moghadam majid jabbari Saeed Daneshmand Saeid Rasouli Jazi Arezoo Khosravi
  10.30495/admt.2021.1923176.1251
• Open Access Article
  • Abstract Page
  • Full-Text
  
  4 - Micro Electropolishing of the MEMS Metallic Structures Fabricated by the Micro WEDM Process
  Mohammad Tahmasebipour Younes Tahmasebipour Mahya Boujari Aliabadi Shadi Ebrahimi
  10.30486/admt.2022.1928592.1277
• Open Access Article
  • Abstract Page
  • Full-Text
  
  5 - Using design of experiments approach and simulated annealing algorithm for modeling and Optimization of EDM process parameters
  Masoud Azadi Moghaddam Farhad Kolahan Meysam Beytolamani
• Open Access Article
  • Abstract Page
  • Full-Text
  
  6 - Investigation of the Impact of the Alumina Powder Presence in Dielectric on Electrical Discharge Machining Parameters of A413 Aluminum Workpiece using Taguchi's Experiment Design, Signal-to-noise Analysis, and Total Normalized Quality Loss
  Mojtaba Shahbazi Dastjerdi Ali Mokhtarian Mojtaba Rahimi
• Open Access Article
  • Abstract Page
  • Full-Text
  
  7 - Intelligent Knowledge Based System Approach for Optimization of Design and Manufacturing Process for Wire-Electrical Discharge Machining
  Morteza Sadegh Amalnik
• Open Access Article
  • Abstract Page
  • Full-Text
  
  8 - An experimental analysis and optimization of machining rate and surface characteristics in WEDM of Monel-400 using RSM and desirability approach
  Vinod Kumar Vikas Kumar Kamal Kumar Jangra
• Open Access Article
  • Abstract Page
  • Full-Text
  
  9 - Multi-objective optimization in WEDM of D3 tool steel using integrated approach of Taguchi method & Grey relational analysis
  Anand S. Shivade Vasudev D. Shinde
• Open Access Article
  • Abstract Page
  • Full-Text
  
  10 - The Effect of Electrical Discharge Machining Parameters On 2024 Aluminum-Based Composite Material Using Calculation and Analysis of the Total Normalized Quality Loss and Signal-to-Noise Analysis
  Behnam Masoudi saeed daneshmand
• Open Access Article
  • Abstract Page
  • Full-Text
  
  11 - Electrical Discharge Machining of Aluminum Matrix Composite Reinforced With Titanium Oxide Nano-Particles
  Ali akbar lotfi Saeed Daneshmand
• Open Access Article
  • Abstract Page
  • Full-Text
  
  12 - Investigation and Optimization of the Effect of Input Parameters on Material Removal Rate, Tool Wear Rate, and Surface Roughness in Electrical Discharge Machining of A356 Nano-Composite Reinforced By Alumina
  Mohammad Javad HajHosseini Ali Mokhtarian Mojtaba Rahimi Behnam Masoudi
• Open Access Article
  • Abstract Page
  • Full-Text
  
  13 - Investigation and optimization of the effect of input parameters on output parameters of electrical discharge machining of A356 nano-composite reinforced by SiC
  Amir Rahmani Ali Mokhtarian Mojtaba Rahimi
• Open Access Article
  • Abstract Page
  • Full-Text
  
  14 - بهینه‌سازی‬ نرخ براده برداری در ماشین‌کاری تخلیه الکتریکی بر روی آلیاژ DIN 1.2080 با کمک روش شبکه عصبی و الگوریتم ژنتیک
  مسعود عظیمی امین کلاه دوز سید علی افتخاری